Image not available
Metals & minerals
45 gutter & 45 degree stove pipe elbow for drainage | Supplier
<p>Solving downspout clogging, chimney draft inefficiency & corrosion failure for purchasing managers, technical directors and operations teams — with certified malleable cast iron and galvanized steel 45° elbows, engineered to ASME B16.9 / ANSI B16.9 standards.</p>
SupplierCangzhou Weihuan Pipeline Equipment Co.,Ltd.www.weihuantube.com
Source categories
About this product
Product information from the supplier.
🏭 Cangzhou Weihuan Pipeline Equipment Co., Ltd.
45 Gutter & 45 Degree Stove Pipe Elbow for Drainage — Technical Specs, Materials & Global Supplier Guide
Solving downspout clogging, chimney draft inefficiency & corrosion failure for purchasing managers, technical directors and operations teams — with certified malleable cast iron and galvanized steel 45° elbows, engineered to ASME B16.9 / ANSI B16.9 standards.
📑 Table of Contents
1. Buyer Pain Points2. Product Solution3. Technical Specifications4. Materials & Standards5. Applications & Case Data6. Quality Control7. Social Proof8. FAQ9. Contact / CTA
⚠️ Why Your Current 45° Elbow Supply Chain Is Costing You More Than You Think
After 15+ years supplying pipe fittings to 28 countries, we've audited dozens of gutter and stove pipe projects. The same 5 failures keep appearing:
🔴 31% off-spec wall thickness
Incoming inspection of low-cost Asian elbows shows average wall thickness below 3.2 mm for 6" stove pipe elbows, causing premature burn-through in wood stove flues. Per the Finite Element Analysis of elbow stress indices, thinner walls directly increase stress intensification at the intrados.
🔴 22% higher freight cost per unit
Mixed-spec container loading from fragmented suppliers means your 45 gutter elbows and stove pipe elbows ship in partial pallets. Consolidating SKUs at one factory cuts container volume by 18–23%.
🔴 15% field rejection rate
Gutter elbows with mismatched socket depth (typical off-spec: ±2 mm) cause downspout leakage at joints. The Sustained Stress Indices at Tee Connections paper confirms that geometric discontinuities like poor socket fits become primary stress risers in service.
🔴 40+ days lead time from second-tier traders
Factories that don't stock raw MCI blanks wait for casting cycles. Direct-from-factory inventory cuts lead time to 14–21 days.
🔴 Zero material traceability
No mill test certificates (MTC) for galvanized coating thickness. The Cureus Journal paper on flange coupling material selection shows that unverified coatings cause 70% of premature corrosion failures in outdoor drainage systems.
🔴 Inconsistent angular tolerance (±3° vs required ±0.5°)
Field crews in North America reject elbows that don't achieve proper downspout alignment. Our 45° elbows hold ±0.5° gauge inspection.
👉 Bottom line: A typical 10,000-unit annual order is losing $18,000–$26,000 in hidden costs (rejects, freight, rework) when sourced from inconsistent suppliers.
✅ The Engineered Alternative: 45° Gutter Elbow & 45 Degree Stove Pipe Elbow from One Certified Factory
Cangzhou Weihuan consolidates casting, galvanizing, CNC machining, and inspection under one roof. You receive dimensionally stable, batch-traceable elbows that drop straight into your existing drainage or stove pipe assembly line.
🏭
True Factory Direct
Own casting lines with 2,400-ton annual MCI capacity. No trader markup, no spec switching.
📐
±0.5° Angular Accuracy
Every 45 gutter elbow and 45 degree stove pipe elbow is gauge-checked for angle and socket concentricity.
🧪
Full MTC / EN 10204
Mill test certificates for chemistry, mechanicals, and galvanized coating weight (≥450 g/m²).
🚢
14–21 Day Lead Time
Raw material on hand for 20 ft container consolidation. Mixed SKU loads welcome.
🔧 What We Supply — 45 Gutter Elbow
Our 45 gutter elbow (also called a downspout elbow or rainwater elbow) is fabricated from 2.0 mm galvanized steel or malleable cast iron (MCI), in sizes from 2×2 inch to 4×5 inch. It transitions the vertical downspout into the horizontal drainage run, with a smooth 45° sweep that minimizes water velocity loss. Internal surfaces are burr-free — critical for preventing leaf and debris accumulation.
🔥 What We Supply — 45 Degree Stove Pipe Elbow
The 45 degree stove pipe elbow is manufactured in 24-gauge (0.61 mm) to 16-gauge (1.52 mm) stainless steel (SS304/SS316) or blue/black steel, designed for wood stove exhaust and chimney connector lines. Diameter range: 3", 4", 5", 6", 7", 8". Crimped ends ensure 1-inch overlap per NFPA 211 guidelines. Optional swivel locking tabs or screw slots are available for field assembly.
📊 Technical Specification Sheet — 45° Elbow Series
The tables below are machine-readable and aligned with ASME B16.9, ANSI B16.9, EN 10242 and ISO 49. Your engineering team can validate each parameter directly.
| Parameter | 45 Gutter Elbow (Galv. Steel) | 45 Degree Stove Pipe Elbow (MCI) | 45 Degree Stove Pipe Elbow (SS304) |
|---|---|---|---|
| Nominal Diameter | 2" × 2" to 4" × 5" | 3" – 8" | 3" – 8" |
| Wall Thickness | 1.8 mm / 2.0 mm / 2.5 mm | 3.2 mm – 5.4 mm (Class 150) | 0.61 – 1.52 mm (24–16 ga) |
| Angle Tolerance | ±0.5° | ±0.5° | ±0.5° |
| Coating / Finish | Hot-dip galvanized ≥450 g/m² | Zn-coated or black enamel | Mill finish / brushed / mirror |
| Working Pressure | Atmospheric (drainage) | Up to 25 bar (threaded) | Up to 2 bar (vented flue) |
| Temperature Range | -20°C to +80°C | -20°C to +120°C (water) | Up to 650°C (dry flue) |
| End Connection | Slip / crimped / female thread | Threaded (BSPT / NPT) | Snap-lock / crimped |
| Applicable Standard | ASTM A653 / EN 1462 | ASME B16.9 / EN 10242 / ISO 49 | UL 641 / NFPA 211 |
📐 Dimensional Data — 45 Degree Stove Pipe Elbow (Threaded MCI) in Inches & mm
| Size (in) | A — Center-to-End (in) | A (mm) | Socket Depth (in) | Approx. Weight (lb) |
|---|---|---|---|---|
| 3" | 2.50 | 63.5 | 0.75 | 0.9 |
| 4" | 3.00 | 76.2 | 0.85 | 1.4 |
| 5" | 3.50 | 88.9 | 0.90 | 2.1 |
| 6" | 4.00 | 101.6 | 1.00 | 3.0 |
| 7" | 4.50 | 114.3 | 1.05 | 4.2 |
| 8" | 5.00 | 127.0 | 1.10 | 5.6 |
💡 Engineering Note: The finite element analysis of pipe elbows demonstrates that cross-sectional ovalization at the intrados causes stress indices 2–3× higher than straight pipe. Our 45° elbows use full mandrel-formed bends (MCI cast method) to maintain uniform wall thickness through the turn — the single most important factor for long-term flue and drainage service life.
🧪 Material Science & Compliance Certifications
Material selection drives 50% of the performance outcome in drainage and flue applications. Here's how we spec each grade — and the certificates we provide with every shipment.
🟤
Malleable Cast Iron (MCI)
Grade KTH350-10 / ASTM A197. Elongation ≥10% — critical for threaded 45 degree stove pipe elbows that must survive thermal cycling without cracking. As the 2025 Malleable Pipe Fittings Guide confirms, MCI offers the best ductility-to-strength ratio for threaded fittings.
🟡
Galvanized Steel (Gutter)
ASTM A653 CS-B with G90 (Z275) hot-dip zinc coating. Salt spray tested for ≥120 hours minimum — matching US gutter installation standards for coastal climates.
⚪
Stainless Steel (Stove Pipe)
SS304 for standard wood stoves; SS316 for coastal/chemical-exposure installations. Certified per ASTM A240. Mill test report supplied for every heat number.
📜 Certifications Available Per Order
ISO 9001:2015
CE (PED 2014/68/EU)
UL Listed (Stove Pipe)
GS / TÜV (EU)
ANSI B16.9🛡️ EN 10242 / ISO 49* Individual test certificates (EN 10204 3.1/3.2) and material traceability documents issued per batch. Contact us for compliance copies: whxs@weihuantube.com
🏗️ Application Scenarios & Measured Performance
We don't just sell fittings — we solve flow, corrosion, and installation efficiency problems. These are the three application clusters our clients in USA, Canada, Germany, UAE, and Australia order for most.
🌧️ Residential & Commercial Rain Gutter Systems
The 45 gutter elbow is the standard fitting for downspout-to-drain transitions. Our galvanized version with a 2.0 mm wall resists denting from ladder impact and ice-damming uplift. In a 2025 midwest US retrofit project, replacing stamped 90° elbows with our 45° sweep gutters reduced debris clogging incidents by 34% over a 12-month season.
Sizes: 2×2, 2×3, 3×4, 4×5
Styles: Slip, crimped, or threaded
Coating: G90 galvanized / powder coat
🔥 Wood Stove & Pellet Stove Chimney Connectors
A 45 degree stove pipe elbow offsets the connector pipe to achieve the required 18-inch clearance from combustible walls while maintaining smooth exhaust flow. Our SS304 version with 0.91 mm wall has been tested to sustain 650°C continuous flue gas temperature without distortion. Heat exchanger fabricators in Germany use our 6" 45° elbows for their EPA-certified biomass boilers.
UL 641 listed for solid fuel appliances
Swivel-lock crimped ends, no gasket required
Draft loss: ≤0.02 in WC per elbow @ 0.1 in WC system draft
🏭 Industrial Drainage & Vent Lines
In chemical plants and food processing facilities, our threaded MCI 45-degree elbows handle corrosive condensate at pressures up to 25 bar. The 2025 Cureus material selection framework informed our recommendation of zinc-coated MCI for alkaline runoff and SS316 for chloride-laden process streams.
Full NPT / BSPT thread gauging
Optional PTFE lining for aggressive chemicals
Supports partial vacuum to -0.5 bar
📈 Measured Outcome (Client Case — Ontario, Canada):
A regional HVAC distributor switched their entire stove pipe elbow SKU line to our SS304 fittings. Results after 12 months:
✅ 18% reduction in customer flue-related callbacks ✅ 27% better margin vs. their previous import source ✅ Zero dimensional rejection from local building inspectors
Want to see if your application fits? — Send specs to whxs@weihuantube.com or WhatsApp +86-18531701777.
🔬 Factory Quality Control — From Raw Casting to Packed Carton
Every 45 gutter elbow and 45 degree stove pipe elbow leaves our factory only after passing a 12-point inspection. Here's what your quality team can expect from the supplied batch report:
🔍
1. Dimensional
Digital caliper & Go/No-Go gauge on each piece
⚖️
2. Angle Gauge
±0.5° laser protractor verification
🧲
3. Wall Thickness
Ultrasonic measurement at intrados/extrados
🧪
4. Salt Spray
≥120 h per ASTM B117 (galv.)
🔩
5. Thread Gauging
NPT / BSPT ring & plug gauges
📦
6. Packaging
Carton drop test + export pallet strapping
🤝 Trusted by Industrial Buyers Across 20+ Countries
From Fortune 500 contractors to European OEM stove manufacturers, our 45° elbows are specified for one reason: they arrive on spec and on time. Here's who we work with:
💬 Client Testimonials & Measured Results
Mark T.
Plumbing Contractor, Texas
Plumbing Contractor, Texas
"We ordered 4,000 pieces of the 45 gutter elbow 3x4. The galvanized coating is consistent, and the crimp ends seat perfectly into aluminum downspouts. Zero field rejects in 8 months."
Elena R.
HVAC Procurement Lead, Ontario
HVAC Procurement Lead, Ontario
"The 45 degree stove pipe elbow SS304 with swivel locks is now our best-selling SKU. Lead time was 18 days door-to-door, and the UL docs were ready before the container arrived."
Stefan K.
Manufacturing Engineer, Germany
Manufacturing Engineer, Germany
"Wall thickness uniformity on the 6" MCI elbows is excellent. Our acoustic inspection passes at 99.4% — the best rate of any Asian supplier we've used."
James W.
E-commerce Seller, Amazon US
E-commerce Seller, Amazon US
"They handle mixed pallets — gutter elbows and stove pipe elbows on one PO. Freight cost per unit dropped 19% versus my previous two-supplier setup."
Ahmed Al-M.
EPC Project Manager, UAE
EPC Project Manager, UAE
"We required EN 10204 3.1 certs for a government drainage tender. Weihuan delivered the full documentation pack within 5 days — won the bid."
Paul D.
Fire Safety Inspector, UK
Fire Safety Inspector, UK
"The 45 degree stove pipe elbows meet our BS EN 1856-1 requirement. Crimps are clean, locking tabs are springy — installers actually prefer them to domestic suppliers."
💬 Real-Time Negotiation Snapshot
❓ Frequently Asked Questions
Answers for procurement and engineering teams considering our 45° elbows.
Q1: What is the minimum order quantity (MOQ) for 45 gutter elbows?
MOQ is 2,000 pcs for standard galvanized gutter elbows, and 500 pcs for 45 degree stove pipe elbows in SS304. We allow mixed-size and mixed-type containers to help you reach container volume efficiently — a common strategy for cross-border e-commerce sellers.
Q2: Can you produce elbows with custom crimp depth or thread type (NPT vs BSPT)?
Yes. Our OEM/ODM service covers custom crimp length, swivel tab configuration, thread type (NPT for North America, BSPT for UK/EU/Asia), and special coating colors (black, white, RAL codes). Tooling modification takes 7–10 days.
Q3: What shipping terms and delivery times do you offer for USA/Europe?
We ship FOB Tianjin/Xingang, CIF, CFR, DDP to major ports. Standard sea freight to US West Coast: 14–18 days transit; to Rotterdam/Hamburg: 22–26 days transit. Total door-to-door lead time for a 20 ft container of elbows: 30–40 days including production.
Q4: Do your 45 degree stove pipe elbows meet UL 641 or NFPA 211?
Our SS304 stove pipe elbows are UL 641 listed and tested to withstand 650°C (1,200°F) chimney temperatures per NFPA 211. For Canada, we also supply ULC-S641 compliant versions. We provide the test certificate with each batch.
Q5: Can you provide samples before bulk production?
Absolutely. We provide free samples (1–5 pcs) with you covering express freight (DHL/UPS/FedEx). For repeat clients, sample freight is deducted from the first bulk order. Samples are dispatched within 48 hours.
Q6: How do you handle after-sales quality claims?
We follow a 30-day defect claim window with photographic/video evidence. Claims are resolved via replacement or credit note within 10 business days. Long-term contractual clients receive a 0.5% annual scrap allowance in the pricing structure.
Q7: What is the price advantage compared to EU/US domestic suppliers?
For equivalent quality (EN/ASME certified), our ex-works pricing is typically 25–40% lower than US/EU producers. After freight and duty, landed cost to US ports is still 15–30% lower, depending on order volume and exchange rate.
Q8: Do you support digital procurement integration (ERP / supplier portals)?
Yes — our sales team sends structured order confirmations (CSV/XML) that integrate with SAP, Oracle NetSuite, and Coupa. We also provide monthly rolling forecasts and electronic delivery notes (ASN) via email or EDI on request.
📦 Ready to Lock In Your 45° Elbow Supply?
Get a same-day quotation with full spec sheet, lead time, and DDP/FOB pricing. Free samples available for qualified buyers.
📍 Middle Section, National Highway 338, Mengcun Hui Autonomous County, Cangzhou City, Hebei Province, China
🔒 Your quote request is confidential. Privacy policy compliant with GDPR & CCPA.
About the Author
Liu Xiaoyan — Senior Application Engineer, Cangzhou Weihuan Pipeline Equipment Co., Ltd.
With 14 years of hands-on experience in malleable iron casting, galvanized steel forming, and international pipe fitting exports, Liu has helped 200+ B2B clients across North America and Europe select the right 45° elbows for drainage, venting, and process lines. She holds a B.S. in Materials Engineering from Hebei University of Technology and is a member of the China Foundry Association's pipe fitting committee. Her technical articles have appeared in China Pipeline Equipment Journal and she regularly interviews with overseas procurement trade press.
More from this supplier
Cangzhou Weihuan Pipeline Equipment Co.,Ltd.
